• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Glass Window Repair

Professional window repairmen work from high off the ground, maneuvering huge panes of glass. They follow strict safety protocols and are often working in extreme weather conditions.

Wearing protective clothing, cut off the glazing points made of metal and the glazing putty by using a utility knife. A heat gun can help soften and remove the old putty.

Replacement

It is tempting to repair the glass of your window instead of replacing it if the glass breaks. However, replacing a window is usually more cost-effective and can assist in preventing other issues in your home's energy efficiency. Examine the kind of glass damaged to determine whether it's a temporary fix, or if a more permanent solution is required.

The first step to repair damaged windows is to take off the sash, or frame and place it flat on a table. Wearing eye protection, gently wiggle the window's pane and then remove any remaining fragments. Utilize a utility blade to scrape off the glazing compound, as well as the glazing points that keep the window in place. Be sure to keep an eye on the components and their locations to make sure they can be put back in place later.

After the frame and sash have been removed, you can begin preparing to install new glass. Before you begin make sure that the opening in the frame is properly sized for your replacement window. To allow for frame and glass expansion and contraction, measure both directions across the opening and subtract 1/8 inch. Then, you can purchase double-strength glasses made to these exact measurements. It is a good idea also to purchase enough glazier's clips, or points to be installed every 6 inches around the window pane.

Depending on the warranty of the window it could be covered by the manufacturer and in this case, you need to contact them to make an claim. After the new glass has been put in place, it is important to cover it with a thin layer of glaziers compound. After the compound has dried and dry, you can paint it to match the rest of the frame.

If the crack is greater than an inch you can stop it from expanding by scoring the crack with a small arc, just above the crack. This method isn't infallible, but it will slow the growth of the crack to a manageable level until you can take more permanent measures.

Repair

Professional window contractors know how to handle a variety of glass and have the tools needed to complete a proper job. They also know the best methods for disposing of waste, so they're less likely to leave crumbs in the trash, which could cause harm to pets or family members. They're also accustomed to working with various types of windows, and they may be aware of issues that might not be apparent to the uninitiated homeowner.

Wear safety goggles and gloves prior to starting the process of repairing cracked glass. Even a small crack can cause shards of glass to fly away and could pose a danger to anyone in or around the home. It's important to determine the cause of the crack, since this will help prevent any future issues.

Make a two-part mixture of epoxy. They are typically 50/50 mix of resin and hardener, and they need to be mixed quickly. After the mixture is made, apply it directly to the crack and let it dry. It should only take about a few minutes, but you must work quickly because the mixture is very thick and will dry very quickly.

Once the epoxy has dried, you can get rid of excess epoxy using a putty blade. The next step is to clean around the cracked glass window repair. If you don't clean the area in a proper manner the debris could cause further damage to your glass. After the glass has been cleaned, use a putty knife to smooth the compound along the edges of the window and to align it with the wood frame.

If you want a more durable solution, consider using a plastic cover. You can cover the glass with masking tape or a strong-duty trash bag. This will keep the crack from growing and will also keep out wind, water insects, water, and other debris.

You can come up with an interim solution when you are unable access the window in an efficient manner. Apply a small amount of silicone sealant around the edges of the broken glass. It won't completely seal the gap between the glass and the frame completely, but it will hold the broken piece in place until you are able to repair it.

Repainting

If your windows with glass are old, you may consider repainting them. This is an affordable alternative to window replacement and will give your home a new look. Make sure the window is clean before painting. Wash the window with soap and water or use ruby alcohol to eliminate oil smudges as well as other residues that can prevent the paint from adhering. Wear rubber gloves when working on glass surfaces to avoid the transfer of oils from your fingers onto the surface. Apply multiple thin coats instead of a single thick one. This will make the paint last longer and keep your windows looking smooth and even.

If you're planning on repainting your glass windows, be sure you have the appropriate tools nearby. You'll need brushes or sponges, painter's tap as well as a ruler and toothpicks. It is also recommended to have the brushes and paint you'll use for the project on hand. Follow the instructions of the manufacturer. Have patience, as it may take some time for the paint to fully dry.

It is also important to ensure that the area you're working in is well ventilated, especially if you're using solvent-based paint. This will decrease the risk of breathing in toxic chemicals and allow the paint to dry more quickly. Wear a mask to protect yourself when using spray paints.

It is necessary to clean the glass window thoroughly using warm water and soap before you paint it. Clean the glass thoroughly with soap and warm water, then use rubbing alcohol to clean away any grease or oil that could hinder paint's adhesion. Make sure that the windows are completely dry before you start coating them.

If your glass windows are energy efficient dual pane windows, you may be eligible to file a claim with the window manufacturer or dealer that sold them to pay any repair or replacement costs. This is especially true if your windows are still under warranty and have experienced multiple problems with condensation or damaged glass.

Sealing

If you have double-pane windows that have a broken seal or a newer version of insulated glass units (IGUs) that have experienced defogging and fogging, there are a variety of options to fix the issue. It is the most expensive option to replace the insulated unit as well as the frame. However, it might be required in situations where fog or condensation is creating energy loss. Other options include replacing the IGU with just one pane, or repairing the IGU that is in place by drilling a hole in the bottom and filling it up with an anti-fogging solution.

You can also close the gap between windows and a threshold or sill by using a felt strip or vinyl V-strip. Felt can be stapled, glued or nailed into place but does not offer much protection against moisture. Vinyl v-strips are simple to put up and is durable however, it can be costly. It is usually used in areas that are exposed to abrasions that are high. Door sweeps are inexpensive and can be fixed to the floor however they provide little to no barrier between the threshold or sill and air, dust, and Glass Window Repair other debris.

To repair a broken window seal, use a putty blade to take off the caulk. Wearing gloves and eye protection remove the glazing point -- tiny fasteners with sharp pointed tips that hold the glass in the recess of the frame. Once you have removed the glazing points, scrub the grooves and sand the wood until it is smooth. Wipe away any sanding sludge and then seal the unfinished wooden surface with a linseed-oil-based paint or clear sealer.

A caulking knife or putty can be used to apply traditional glazing putty, however a knife will provide an easier application and a better seal. Choose a putty specifically for glass, as it is more durable and stick better.

Apply a small amount the putty on the inside edge of the frame where it meets the glass. Slide the window into the frame so that the drawn line on the glass aligns with the edge of the frame. Apply pressure to the glass in order to force the putty to form a tight seal. Smooth the compound using a gloved finger, and wipe away any caulk that is applied incorrectly or spills that are not properly wiped away before it is dry.